PROC m_fl_vlimit
;Version 2			
GOTO BEGIN
;
;#**************************************************************************
;#	****PROCEDURE HEADER****
;#
;# 	1.0 	Introduction
;#
;#		1.1	FOT Name:	M_FL_VLIMIT
;#		    MMS-F Name:	
;#		    SUM Issue:	
;#			Simulator Validation Status:
;#
;#		1.2	Date Created:	9/27/94
;#				Revision: 1. 5-26-95
;#					 	2. 11/18/95 GJ	
;#
;#		1.3	Change Description:	
;#
;#			1.  Corrected syntax errors
;#			2.  Changed name convention from m_ts_* to m_fl_*.
;#
;#		1.4	Point of Contact:	
;#			FOT Author: RRowe	ATSC/SOHO	805-3642
;#
;#**************************************************************************
;#	2.0	Description
;#
;#		2.1	Narrative Description
;#
;#			This procedure sets and enables limit checking for the 
;#			spacecraft power systems parameters and MDI internal
;#			voltage monitors.
;#
;#		2.2	Intended Use:
;#
;#			Establish limits for MDI S/C and internal voltages which
;#			may identify hardware risk issues if violated.
;#
;#		2.3	Duration:	TBD
;#
;#		2.4 References:
;#
;#**************************************************************************
;#	3.0	Instructions for Use:
;#
;#		3.1	Parameters Required
;#
;#			None
;#
;#		3.2	Critical Activities
;#
;#			TBD
;#
;#		3.3	Special Constraints or Activities
;#
;#			MDI in SLEEP or higher mode.  This procedure should
;#			be completed as part of the MDI power on.  All values
;#			TBR.  Red action limits on m+5cm and m+5pc2n.
;#**************************************************************************
;#	4.0	STEPS:
;#		
;
BEGIN:

IF (P@CMD_STATE#TELECOMMAND = "AVAILABLE") THEN
ELSE
	/CLEAR		;Clearing the Command Buffer.
ENDIF
;
;				'GO' to set the limits for the S/C power
;				system parameters an MDI internal voltage
WAIT;				monitors.
;
;
;				Set the voltage limits for S/C monitors
;
LIM CHANGE M+5PC1N  EU 1 LIMVAL   4.0   4.5   6.5   7.0
LIM CHANGE M+15PC1N EU 1 LIMVAL  13.0  14.0  17.5  18.0
LIM CHANGE M-15PC1N EU 1 LIMVAL -17.0 -16.0 -14.0 -13.0
LIM CHANGE M+5PC2N  EU 1 LIMVAL   4.0   4.5   6.5   7.0
LIM CHANGE M+15PC2N EU 1 LIMVAL  13.0  14.0  17.0  18.0
LIM CHANGE M-15PC2N EU 1 LIMVAL -17.0 -16.0 -14.0 -13.0
;
;
;				Set the voltage limits fot MDI monitors
;
LIM CHANGE M+5IP    EU 1 LIMVAL   4.0   4.5   6.0   7.0
LIM CHANGE M+5CM    EU 1 LIMVAL   4.0   4.5   6.0   7.0
LIM CHANGE M+15CM   EU 1 LIMVAL  13.0  14.0  17.0  18.0
LIM CHANGE M-15CM   EU 1 LIMVAL -17.0 -16.0 -14.0 -13.0
LIM CHANGE M+30CM   EU 1 LIMVAL  25.0  27.0  38.0  40.0
LIM CHANGE M+5AE    EU 1 LIMVAL   4.0   4.5   6.0   7.0
LIM CHANGE M+15AE   EU 1 LIMVAL  13.0  14.0  17.0  18.0
LIM CHANGE M-15AE   EU 1 LIMVAL -17.0 -16.0 -14.0 -13.0
LIM CHANGE M+15MTR  EU 1 LIMVAL  13.0  14.0  19.0  20.0
LIM CHANGE M+15HTR  EU 1 LIMVAL  13.0  14.0  19.0  20.0
LIM CHANGE M+75LT   EU 1 LIMVAL  65.0  70.0  80.0  85.0
;
;
;				Turn the MDI voltage limits ON
;
;
LIM ON M+5PC1N
LIM ON M+15PC1N
LIM ON M-15PC1N
LIM ON M+5PC2N
LIM ON M+15PC2N
LIM ON M-15PC2N
LIM ON M+5IP
LIM ON M+5CM
LIM ON M+15CM
LIM ON M-15CM
LIM ON M+30CM
LIM ON M+5AE
LIM ON M+15AE
LIM ON M-15AE
LIM ON M+15MTR
LIM ON M+15HTR
LIM ON M+75LT
;
;#************************************************************************** 
;#	5.0	Final Constraints
;#
;#		TBD
;#
;#**************************************************************************
ENDPROC